• <menu id="akma8"></menu>
    當前位置:沈陽機床集團股份有限責任公司新聞中心數控技術 常見數控機床報警信息中英文對照

    常見數控機床報警信息中英文對照

    日期:2015-03-30 09:20:37 作者: 來源: 瀏覽次數:0
       T WORD ERROR (T 碼錯誤)
      LOW OIL LEVEL (油位低)
      SPINPLE FAULT (主軸故障)
      SPINDLE ALARM (主軸報警)
      EXTERNAL EMG STOP (急停按鈕被按下)
      AC NOT READY (交流盤未準備好)
      SPINPLE LUBE FAULT (主軸潤滑故障)
      T CODE ERROR (T代碼出錯,非法T代碼)
      M CODE ERROR (M代碼出錯,非法M代碼)
      SERVO NOT READY (伺服未準備好)
      NC NOT READY(NC沒準備好)
      TURRET FAULT (轉塔故障)
      TURRET LIMIT (轉塔限位)
      DC 24V OPEN (直流24斷開)
      +24V NOT READY(+24V沒準備好)
      GRAR DRIFT (檔位漂移)
      PLEASE AXIS RETURN HOME(軸未回零)
      PLEASE DRUM RETURN HOME(刀庫未回零)
      AIRPRESSFAILURE(氣壓故障)
      UNCL TOOL FALL(松刀失。
      AIR PRESSURE DROP (壓縮空氣壓力過低)
      CLAMP TOOL FALL(夾刀失。
      DRUM NOT PARKED(刀庫未在原值)
      X ZERO POINT NOT REACHED (X 軸未回零)
      Y ZERO POINT NOT REACHED (Y 軸未回零)
      Z ZERO POINT NOT REACHED (Z 軸未回零)
      4TH ZERO POINT NOT REACHED (第4軸未回零)
       
      X AXIS OVERTRAVL(X軸超限)
      Y AXIS OVERTRAVL (Y軸超限)
      Z AXIS OVERTRAVL (Z軸超限)
      COUNTER SWITCH REEOR (計數開關故障)
      MASTERT RANSFER OVER TEMP (主變壓器過熱)
      Z AXIS NOT AT FIRST REF POSITION (Z軸未在第一參考點)
      SPINDLE ORIENTATION FALLURE (主軸定向失。
      TOOL DESENT OR TOOL DATA REEOR (刀具數據錯誤)
      PLEASE UNLOAD THE TOOL ON SPRINELK (請卸下主軸上的刀)
      PLEASE LOAD TOOL ON APINDLE (請裝上主軸上的刀)
      A AXIS UNCLAMP FAIL (A 軸松開失。
      A AXIS CLAMP FAIL (A 軸夾緊失。
      DRUM OUT TO APRONDLEIS FALL (刀庫擺向換刀位失。
      MG SWING OVERLOAD(刀庫擺動過載)
      DRUM BACK PARK IS FALL (刀庫擺回原始位失。
      TURRENT MOTOR1 OVERLOAD (刀庫移動電機過載)
      COOLANT MOTOR OVERLOAD (冷卻泵過載)
      DRUM ATC FAULT (自動換刀失。
      TOOLS UNLOCKED (刀具未鎖緊)
      BATTERY ALARM (電池報警)
       
      DRUM POSITION SWITCH ERROR (刀庫位置檢測開關故障)
      DRUM NOW NOT AT PARK (刀庫未在原始位置)
      IT DANGOU TO MOVE DRUM (刀庫禁動)
      POT UO FAILOR POT NOT AT UP POSITION (刀套未在水平位)
      POT DOWN FAIL (刀套翻下動作失。
      IT IS DANGOUR TO MOVE ARM (機械手禁動)
      THE SPINDLE STATU IS ERROR (主軸狀態錯誤)
      ARM MOTOR OR ARM SWITCH FALL (機械手或機械手開關故障)
      CENTRE LUBRICATION FALL (中心潤滑故障)
      THE WORK NOT CLAMPED (工件未夾緊)
      AUTO TOOL CHANGE FAULT (自動換刀失。
      TOOL DATA OUT OF RANGE (指令刀具號超出范圍)
      THE ORDER TOOL NOW IN SPINDLE (目標刀具在主軸上)
      THE THREE SPINDLE SWITCH FAULT (主軸上的接近開關)
      THE CENTRE COOLANT IS LOWER (刀具內冷泵液位過低)
      DRUM RETURN 1# POSITION FAULT (刀庫自動回零失。
      SPINDLE OVERLOAD (主軸過載)
      關注我們的微信公眾號shukongzhpngguo,獲取更多數控技術文章。
      TURRENT MOTOR OVERLOAD (刀盤轉動電機過載)
      CHIP CONVEYER OVERLOAD (拉屑器過載)
      HARD LIMIT OR SERVO ALARM (硬限位或伺服報警)
      NO LUB OIL (無潤滑油)
      INDEX HEAD UNLOCKED (分度頭未鎖緊)
      MT NOT READY(機床沒準備好)
      MG OVERLOAD  (刀庫過載)
      LUB EMPTY(潤滑無油)
      AIR PRESSURE(氣壓不足)
      COOLANT NOT READY(冷卻沒準備好)
      LUBE EMPTY(油霧油位低,潤滑油位低)
      LUB PRESSURE LOW(潤滑壓力低)
      CONVEY  VERLOAD(排屑過載)
      LUB OVERLOAD(潤滑過載)
      LUBE PRESSURE LOW(油霧壓力低)
       
      SERIAL SPINDLE ALARM (串行主軸報警)
      NC BATTERY LOW ALARM(NC電池低報警)
      MAGAZINE MOVE LIMIT SWITCH ERROR
      SPINDLE TOOL UNLAMP POSITION LIMIT SWITCH ERROR
      MAGAZINE NOT IN POSITION OR SENSOR ERROR
      AIR PRESSURE LOW ALARM(氣壓低報警)
      MOTOR OVERLOAD(電機過載)
      T CODE > MAGAZINE TOOLS
      T CODE < 1 ERROR
      5TH AXIS HARDWARE OVERTRAVER LIMIT ERROR
      DOOR IS OPENED(開門)
      LUB PRESSURE SWITCH ERROR(油壓開關錯誤)
      SPINDLE OIL COOLANT UNIT ERROR
      SPINDLE LOAD ABNORMAL(主軸負荷異常)
      TRANSDUCER ALARM(傳感器報警)
      BED-HEAD LUBRICATE OFF(床頭潤滑關閉)
      EMG OFF
      HYDRAULIC CHUCK PRESS LOW(液壓夾頭壓力低)
      HYDRAULIC TAIL PRESS LOW(液壓尾座壓力低)
      LUB 0IL LOW(油壓低)
      TURRET CODE ERROR(轉塔碼錯誤)
      TURRET RUN OVERTIME(轉塔運行超時)
      MANUAL HANDLE INTERRUPT
      TRY TO RUN SPINDLE WHILE CHUCK NOT LOCK
      TRY TO RUN SPINDLE WHILE TAIL NOT LOCK
      SPINDLE NEUTRAL GEAR
      MAGAZINE ADJUST
      HYDRAULIC NOT RUN
      SAFETY DOOR BE OPENED
      SAFETY DOOR NOT CLOSE
      NOT ALL AXIS HAVE GONE BACK REF
      IN ADJUST,IGNORE GOING BACK REF
      AFTER EXCHANGE TOOL,CYCLE START
      ATC MOTOR QF16 OFF
      X AXIS IS LOCKED(X 軸被鎖定)
      Y AXIS IS LOCKED(Y 軸被鎖定)
      Z AXIS IS LOCKED(Z 軸被鎖定)
      A AXIS IS LOCKED(A 軸被鎖定)
      SPINDLE MOTOR FAN QF26 OFF(主軸電機風扇QF26關閉)
      關注我們的微信公眾號shukongzhpngguo,獲取更多數控技術文章。
      SPINDLE ORIENTATION INCOMPLETE(主軸定位不完全)
      M FUNCTION NOT COMPLETE(M 功能無法完成)
      SPINDLE NOT IN GEAR POSITION(齒輪不在主軸位置)
      SPINDLE NOT CHANGED TO LOW GEAR(主軸沒有變為低檔)
      SPINDLE NOT CHANGED TO HIGH GRAR(主軸沒有變為高檔)
      MAG NOT BACKWARD
      SPINDLE TOOL NOT CLAMP
      SPINDLE TOOL NOT UNCLAMP
      MAG NOT IN POSITION
       
      MAG DOES NOT ROTATE
      MAG DOES NOT STOP RUNNING
      A AXIS HAVE NOT CLAMPED
      A AXIS HAVE NOT UNCLAMPED
      SET D499=1,"MAG.JOG" SWITCH ON
      HYDRAULIC MOTOR QF7 OFF( 液壓馬達QF7關閉 )
      HYDRAULIC TEMPRETURE HIGH( 液壓使用溫度高 )
      HYDRAULIC FILTER BLOCKED(液壓過濾器阻止)
      HYDRAULIC OIL LEVEL LOW( 液壓油位低 )
      HYDRAULIC FAN QF8 OFF(液壓風扇QF8關閉)
      HELIX CONYER QF9 OR QF10 OFF
      CHAIN CONYER QF11 OFF
      COOLANT MOTOR QF12 OFF(冷卻液電機QF12關閉)
      COOLNT LEVEL LOW,CYCLE STOP AFTER 20 MINUTES
      INNER COOLANT BLOCK(內冷卻堵塞)
      SPINDLE COOLANT MOTOR QF14 OFF(主軸冷卻液電機QF14關閉)
      INNER COOLANT QF13 OFF(內冷卻液QF13關閉)
      MAG MOTOR QF15 OFF
      CABINET COOLANT EQUIP QF20 OFF
      OIL GATHER QF24 OFF
      AIR PRESSURE LOW(低氣壓)
      SPINDLE COOLANT MOTOR FAULT(主軸冷卻液電機故障)
      LUB.OIL IS LOW(潤滑油低)
      DOOR OPEN(門打開)
      FRONT DOOR(R) OPEN(前門打開)
      LEFT DOOR OPEN(左門打開)
      LUBRICATION OIL QF23 OFF(潤滑油QF23關閉)
      LUBRICATION PRESS LOW(潤滑油位低)
      IN ADJUST,MAG CAN'T EXCHANGE T(在調整,刀庫不能交換T)
      NOT ALL DOOR CLOSED(門沒有全部關閉)
      IN M06,MAG NOT READY(在M06,刀庫未準備好)
      MAGAZINE NOT READY(刀庫未準備好)
      POCKET NOT HORIZANTAL
      IN M06,Z NOT BACK TO 2ND REF
      IN M06,Z AXIS NOT IN PSW1
      ATC NOT IN ZERO POSITION
      SPINDLE ORIENTATION UNCOMPLETE
      POCKET NOT HOR./MAG NOT BCKWRD
      POCKET NOT VER./MAG NOT FORWRD
      UNCLAMP TOOL HAS NOT COMPLETED
      CLAMP TOOL HAS NOT COMPLETED
      AIM TOOL NO. IS WRONG
      MAG NOT BACKWARD
      AFTER RETRACT,SET R.T.BACK OFF
      Z NOT IN PSW2,FORBID ATC RUNNING
      D499 EQUAL 1
       
      MAG.JOG SOFT SWITCH IS ON
      Z NOT IN PSW2,FORBID MAG FORWARD
      CHEKE SPINDLE MODULE ALARM
      OIL WATER SEPARATOR QF24 OFF
      SET THE SOFT SWITCH MAG.JOG OFF
      SET D499 TO 0  設定D499為0
      K PARAM ABOUT MAG SET IS WRONG  關于MAG的K參數設定錯誤
      MECHANICAL BRAKE NOT RELEASED機床抱閘沒有松開
      MECHANICAL BRAKE IS WRONG  機床抱閘錯誤
      PLEASE ADD LUB.OIL  請加潤滑油
      PROBE BATTERY VOLTAGE IS LOW  探頭電池電壓低
      PROBE IS ERR  探頭錯誤
      PARAMETER WRITE ENABLE(參數寫使能)
      PMC EDIT ENABLE(PMC編輯使能)
      CHECK LUB ROUTIN
      SPINDLE GEAR SIGNAL MISS  主軸檔位信號消失
      T_CLAMPED_SIGNAL MISS    T夾緊信號消失
      SP OVERRIDE SWITCH DISCONNECTION   主軸倍率開關斷路
      FEED OVERRIDE SWITCH DISCONNECTION  進給倍率開關斷路
      THE TOTAL NUMBER OF POCKETS SET ERR
      CHANGE T STOPED BECAUSE NO AIR 因為缺少壓空交換停止
      THE COOLANT WATER TOO LOW,ADD COOLANT WATER AT ONCE 冷卻水少立即加水
      COOLANT LEVEL LOW,ADD COOLANT WATER  冷卻水液位低
      PLEASE REPLACE CNC BATTERY QUICKLY  請立即更換CNC電池
       
      SIEMENS常用縮略語
      A Output    輸出
      ASCII American Standard Code for Information Interchange 美國信息交換標準代碼
      AV Preparation for work 運行準備
      BA Operating mode 運行方式
      BAG Operating mode groups 運行方式組
      BB Ready for operation 準備好運行
      BCD Binary Coded Decimals 二-十進制
      BHG Hand-held terminal 手提終端
      BOF User interface 用戶接口
      CNC Computerized Numerical Control 計算機化數字控制
      CP Communication Processor 通迅處理器
      CPU Central Processing Unit 計算機中央處理裝置
      CR Carriage Return 托架折回
      CSB Central Service Board(PLC module) 中央維護板,PLC 模塊
      CTS Clear To Send 發送使能
      DAU Digital-Analog Converter 數模轉換器
      DB Data Block 數據塊
      DIN German Industrial Standards 德國工業標準
      DIO Data Input/Output 數據輸入/輸出
      DRF Differential Resolver Function 差分功能
      DRY Dry Run 空運行
      DSB Decoding Single Block 譯碼單段
      DSR Data Send Ready 備用輸入
      DW Data Word 數據字
      E Input 輸入
      EIA-Code Special tape code,number of holes per characters always odd 特殊紙帶碼,每個字符的孔數為奇數
      EPROM Programm memory with fixed program 有固定程序的程序存儲器
      E/R Controlled Supply and Energy Recovery Module 可控電源和能量恢復模塊
      ETC ETC key:Extension of the softkey bar in the same menu
      ETC 鍵:同級菜單擴展鍵
      FDB Product designation database 產品指定數據庫
      FIFO First in First Out 先進先出
      FRA Frame module 幀頻模塊
      FRAME Coordinate conversion with the components zero
      offset,rotation,scaling,
      mirror-imaging 坐標換算,具有零點偏置,坐標旋轉,標度功能和鏡向功能
      FRK Cutter radius compensation 銑刀半徑補償
      FST Feed Stop 停止進給
      GUD Global User Data 全體用戶數據
      HMS High-Resolution Measuring System 高分辨率測量系統
      HSA Main Spindle Drive 主軸驅動
      HW Hardware 硬件
      IM Interface Module 接口模塊
      IM-S/R Interface Module(S=send/R=receive) 接口模塊,S=發送/R=接收
      INC Increment 步進增量
      ISO-Code Special tape code,number of holes per character always even
      特殊紙帶碼,每個字符的孔數為偶數
      K1...k4 Channel 1 to Channel 4 通道1 到通道4
      KOP Ladder Diagram 梯形圖
      KV Loop-Gain Factor 增益系數
      KUE Transformation Ratio 傳動比
      LCD Liquid Crystal Display 液晶顯示
      LED Light Emitting Diode 發光二極管顯示
      LUD Local User Data 局部用戶數據
      MB Megabyte 兆字節
      MD Machine Data 機床數據
      MK Measuring Circuit 測量回路
      MDA Manual Data Automatic 手動輸入,自動執行
      MLFB Machine-readable product designation 機器可識別的產品代號
      MMC Man Machine Communication:User interface of the numerical control
      system for operation,programming and simulation 人機通訊:系統操作界面,用操作,編程和模擬
      MPF Main Program File:NC part program(main program)
      NC 零件程序,主程序
      MPI Multi Point Interface 多點通訊接口
      MSTT Machine control panel 機床控制面板
      NC Numerical Control 數字控制
      NCK Numerical Control Kernel(numerical krnel with block preparation,
      traversing range etc.) 數字控制核心:具有程序段預處理,運行范圍等等
      NCU Numerical Control Unit 數控單元
      NURBS Non Uniform Rational B Spline 非均值有理B樣條
      NV Zero Offset 零點偏置
      OEM Original Equipment Manufacturer 原設備制造商
      OP Operator Panel 操作面板
      OPI Operator Panel Interface 操作面板接口
      PC Personal Comprter 個人計算機
      PCMCIA Personal Computer Menory Card International Association 接口協議
      PG Programming Device 編程器
      PLC Programmable Logic Control 可編程邏輯控制器
      PRT Program Test 程序測試
      RAM Random Access Memory 隨機存取存儲器
      RISC Reduced Instruction Set Computer 處理器,具有指令組小、通過能力強
      ROV Rapid Override 快速修調
      RPA R Parameters Active(NCK memoty area for R parameter numbers)
      R 參數有效,NCK 中用于R 參數號的存儲器區
      RTS Request To Send(control signal from serial data interfaces)
      發送請求:來自串行接口的控制信號
      SBL Single Block 單段
      SBL2 Single Block Decoding 譯碼單段
      SEA Setting Data Active(memory area for setting data in NCK)
      設定數據有效:用于NCK 中設定數據的存儲區
      SD Setting Data 設定數據
      SKP Skip Block 程序段跳躍
      SM Signal Module 信號模塊
      SPF Sub Program File 子程序文件
      SPS Programmable Logic Controller 可編程邏輯控制器
      SRK Cutter Radius Compensation 刀尖半徑補償
      SSFK Leadscrew Error Compensation 絲杠螺距誤差補償
      SSI Serial Synchronous Interface 串行同步接口
      SW Software 軟件
      TEA Testing Data Active(with reference to the machine data) 測試數據有效:與機床數據有關
      TO Tool Offset 刀具補償
      TOA Tool Offset Active(memory area for tool offset) 刀具補償有效,用于刀補的存儲區
      TRANSMIT Transform Milling into Turning(coordinate conversion on
      turning machines for milling)
      銑床轉換為車床:車床坐標換算用于銑削加工
      VSA Feed drive(spindle) 主軸進給驅動
      V Bit type PLC variable PLC變量類型:位
      VB Byte type PLC variable
      PLC變量類型:字節
      WKZ Tool 刀具
      WZ Tool 刀具
      WZK Tool offset 刀具補償
      ZOA Zero Offset Active(memory area for zero offsets)
      零點偏置有效:零點偏置存儲區

    相關產品推薦
    亚州AV,免费午夜无码18禁无码影院,性BBBBWWBBBB,肥妇大BBWBBWBBWBBWBBWBBW深夜福利备好纸巾18禁止 男女啪啪进出阳道猛进网站 久久精品国产国产精品四凭 又黄又湿啪啪响18禁男男 亚洲精品不卡AV在线播放 超碰人人爽爽人人爽人人 国产AV永久精品无码 美女裸身无遮挡全免费视频全部 小14萝裸体洗澡视频免费网站 大学生扒开粉嫩喷白浆 亚洲AV永久无码精品4K岛国 久久久久人妻精品一区二区三区 德国老妇激情性XXXX 强辱丰满的人妻HD高清 香蕉久久精品日日躁夜夜躁 国内真实愉拍系列在线视频 波多野结衣亚洲AV无码 麻豆国产成人AV高清在线 久久综合精品国产丝袜长腿 免费午夜无码18禁无码影院 美女裸体扒开尿口桶到爽 女高中生自慰免费观看WWW 久艾草久久综合精品无码国产 农民工嫖妓50岁老熟女 护士的色诱2在线观看免费 强行挺进朋友漂亮的娇妻 香蕉久久精品日日躁夜夜躁 朋友出差玩弄人妻系列合集h 女人久久www免费人成看片 人妻在卧室被老板疯狂进入